LED Tape 7.2W/M IP65 (Priced Per Metre)

LED tape with 30 LEDs per metre provides a subtle lighting effect. With an energy consumption of 7.2 watts per metre, it produces half of the brightness compared to our more popular 60 LEDs per metre version, which is available from the related products.

With a self adhesive backing, LED strip tape is easy to install, smaller installations can be done in a matter of minutes with no experience required. It can be cut down as short as 100mm for 12V and 167mm 24V, offering a versatile and flexible lighting solution. Allowing you to illuminate the exact length or area want to.

As part of our 'LED Strip Fit' range we are able to supply the strips to your exact specifications. This includes pre-cut strips with input cables or output connections for bends or joining to other strips. We can included soldered connecting cables to any length you desire. Longer installations (over 10M) require a bit more planning so feel free to contact us directly and we will advise on the best possible solution for your project.

Rated at IP65, it is water and dust resistant and is manufactured with new improved silicone drop resin which improves heat dissipation and increases its life expectancy. Available in 2700K extra warm white, 3000K warm white, 4000K cool white colour temperatures. For RGB colour changing we recommend going with our 60 LEDs per metre version.

Specification

• LEDs per metre: 30 LEDs per metre.
  
• Colour temperatures:
  - 2700K Extra warm white
  - 3000K Warm white
  - 4000K Cool White
  - RGB Colour changing (available in 60 LED/M only)
• Voltage: Available in 12V DC (2700K & 3000K) or 24V DC (4000K only)
• Wattage: 7.2 watt per metre
  
• Lumens: see summary table below. 
  
• LED type: SMD5050
  
• Beam angle: 120 degrees
  
• CRI: 80
• LED chip type: Epistar
• Dimmable? Yes but the right LED driver or controller must be selected:
  - For single colour strips check out our mains dimmable LED drivers. CLICK HERE.
• Life expectancy: 50,000 hours
  
• Guarantee: 3 years
  
• Rated at IP65 full water and dust resistant
  
• Approvals: RoHS, CE and FCC.
  
• Brand: LED Strip Fit
• Lumen output and cut points: See tables below:

Power Supplies

Because these LED strips are low voltage (12V or 24V DC) they require a power supply (or LED driver) to power them. It is important to select the correct one to meet the demands of your application.

The rating of the power supply is determined by the length of strip you require. See our tables of power below for some examples:

Controllers

Depending on your application and which type of LED strip you require, you may need a controller. If you're using single colour LED strip they can be switched on and off by a light switch. You would need to wire the LED driver into your lighting circuit. If you wanted to dim single colour LED strips, you can dim them using a ordinary dimmer switch but you will need a mains dimmable LED driver which we also have in stock.

Other Accessories

For longer runs, usually over 10 metres you may require additional amplifiers or cables. Or you can wire each 10M section directly back to the LED drivers, this avoids 'volt drop' issues. We can also supply any LED strip with a pre-soldered connecting cable to any length you need. 

Design

Our experienced design team can help you plan out your installation every step of the way. We can provide you with your own personal wiring diagram and help you select the right LED drivers and accessories. If you've got some plans or just an idea please contact us for advice.

• Width: 10mm
  
• Height: 3mm
  
• Length: Priced per metre but available in any length from 100mm (167mm for 24V)  cut point) to 100+ metres.
  

30 LEDs Per Metre 12V

• LEDST30EW - Extra warm white 2700K
• LEDST30WW - Warm white 3000K

30 LEDs Per Metre 24V

• LEDST30CW/24V - Cool white 4000K