LED Tape Colour Changing RGB (Priced Per Metre)

Colour changing LED tape known as RGB (red, blue & green) allows you to mix the primary colours to provide a multitude of colours. LED tape is easy to install, smaller installations can be done in a matter of minutes with no experience required.

Available in various IP ratings, with IP20 offering no resistance to water, IP65 offering resistances to splashes and sprays, and IP68 which is completely water resistant. Our RGB LED strip has a self adhesive backing, which can be peeled off and stuck to any clean surface. We can supply this by the metre or it can be cut down to any length you want, allowing you to illuminate the exact length or area you need to.

As part of our 'LED Strip Fit' range we are able to supply the strips to your exact specifications. This includes pre-cut strips from as small as 50mm ranging to 100+ metres. We can included soldered connecting cables to any length you desire. Longer lengths require a bit more planning so feel free to contact us directly and we will advise on the best possible solution for your project.

'LED Strip Fit' tape is now available in various IP ratings including our new fully water resistant IP68 version that can be used outdoors.

Specification

• LEDs per metre: 60 or 96 LEDs per metre.
• Voltage: Available in 12V DC or 24V DC
  
• Priced per metre
• Wattage: 14.4W per metre. New even brighter 23W version available with 96 SMD5060 LEDs per metre.
  
• Colour changing, select between an array of colours by mixing between red, blue and green. Also available in RGB+WW which includes a separate row of warm white LED strip.
• Available in IP20, IP65 rated and IP68
• LED type: SMD5060
  
• Beam angle: 120 degrees
  
• CRI: 75
• Lumens: 960 per metre - and 1056 lumens for the 23W per metre version
• LED chip type: Epistar
• Dimmable: Yes, colour changing strips require a non-dimmable driver as the controller does the dimming and colour changing. CLICK HERE.
• Life expectancy: 50,000 hours
  
• Guarantee: 3 years
• Approvals: RoHS, CE and FCC.
  
• Brand: LED Strip Fit

Power Supplies

Because these LED strips are low voltage (12V or 24V DC) they require a power supply (or LED driver) to power them. It is important to select the correct one to meet the demands of your application.

The rating of the power supply is determined by the length of strip you require. Our table of power below shows some examples of 12V and 24V LED drivers:

Controllers

Colour changing (RGB) LED strip requires a controller to allow you to change colours. It also lets you change between different lighting effects such as fade in / out and flashing modes etc. Our LED controllers range from basic infra-red to more advanced RF (radio frequency) to Wi-Fi controlled. Some of our RF and Wi-Fi controllers allow multiple runs of strips to be controlled wireless. This allows different runs to be controlled at the same time without having to run an a cable between them.

Other Accessories

For longer runs, usually over 10 metres you may require additional amplifiers or cables. We can also supply any LED strip with a pre-soldered connecting cable to any length you need. 

Design

Our experienced design team can help you plan out your installation every step of the way. We can provide you with your own personal wiring diagram and help you select the right LED drivers and accessories. If you've got some plans or just an idea please contact us for advice.

• Width: 10mm
  
• Height: 3mm
  
• Length: Priced per metre but available in any length from 50mm in 12V or 100mm in 24V.

60 LEDs Per Metre

• LEDST60RGB - 12V (IP65)
• LEDST60RGB/24V(IP20) - 24V (IP20)
  
• LEDST60RGB/24V - 24V (IP65)
• LEDST605060IP68RGB - 24V (IP68)
  

96 LEDs Per Metre

• LEDST96RGB/24V - (IP65)
  
• LEDST506096IP68RGB - 24V (IP68)